Water-Based Concrete Bond Breaker. This is your first post. Stake for Screed Key and Load Key If TILT-CRETE application as a cure to the casting slab is delayed for several hours or until the following day, the surface should be moistened with water before application of TILT-CRETE. the mix water from the panel, which results in an easy to lift panel and a strong, smooth, uniform and clean panel Charcoal Color Closed Cell Polyurethane. 0000016497 00000 n Stud Rail ASTM International, 2018. If a curing or curing-and-sealing compound other than 1100 or VOCOMP series products are used, they must be removed prior to the application of TILT-CRETE. TILT-CRETE is not recommended to be used with any other manufacturers bond-breakers. Curing: 200 400 sq. The gaskets are generally available in either PVC, complying with ASTM D2287, Standard Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds (ref. Bond Breaker Geotextile - US Fabrics Apply the second coat of TILT-CRETE at right angles to the previous coat. Standard Specifications for Loadbearing Concrete Masonry Units, ASTM C90-16a. TILT-CRETE has excellent stability and does not require continuous mixing throughout the application process; the material must be mixed only prior to application. Privacy and Cookies Policy endstream endobj 4 0 obj << /Type /Page /Parent 18 0 R /Resources 5 0 R /Contents 6 0 R /MediaBox [ 0 0 612 792 ] /CropBox [ 0 0 612 792 ] /Rotate 0 /Annots 67 0 R >> endobj 5 0 obj << /ProcSet [ /PDF /Text ] /Font << /TT2 28 0 R /TT4 29 0 R /TT6 30 0 R >> /ExtGState << /GS1 33 0 R >> /ColorSpace << /Cs6 31 0 R >> >> endobj 6 0 obj << /Length 2544 /Filter /FlateDecode >> stream The transition slabs deform to dissipate the thermal movements of the bridge. 825ml Tube (28 Oz). Wedge (for use with Recess Member) How fast does the bond breaker dry once it has been applied? 0000000016 00000 n TILT-CRETE cures the concrete floor or casting slab and top sides of panels once poured. It is applied to the casting slab to function as a bond breaker between the casting slab and the tilt-up or lift-slab panel. The product should be used where appearance is a prime consideration in tilt-up and lift-slab construction. W. R. MEADOWS technical services department, Solvent-Based Curing and Sealing Compounds, Meets the moisture retention requirements of ASTM C 309 on steel-troweled surfaces. Toggle Coil Ties 8). <<2F6130032B3F7D4E822F4C36175224FC>]/Prev 134655/XRefStm 1837>> TILT-CRETE concrete cure and bond-breaker is a new, innovative, unique formula of proprietary, reactive organic materials in an aqueous dispersion. Please let us know here why this post is inappropriate. Name may only contain letters, numbers and the characters : - _ or space. Sure Lock Tie Attachment can be made with construction adhesive, nails or staples. Figure 3h is a variation on this approach, where one horizontal bond beam reinforcing bar extends across the control joint, and is similarly debonded to allow longitudinal movement. Concrete mix designs that contain in excess of 20% pozzolans such as fly ash may require additional coats of the bond breaker. WebEnter a new name for this list: This is a required field. NOTE: Panels sticking to the casting slab is the result of insufficient or improper application of the bond-breaker, i.e. %PDF-1.4 % CAUTION: TO AVOID FOAMING, DO NOT MIX EXCESSIVELY. Not compatible with hot pour sealants or some chemical sure sealants. Concrete Accessories | Bond Breakers This keeps the joint weather tight while accommodating small movements. Bond breakers are used over concrete surfaces to eliminate or reduce the cracking of slabs due to temperature and moisture fluctuations. is the proper isolation joint to use A recent discovery has been leaked about the real Root cause of gum disease And tooth decay, and it has Continue reading A50. strongback Tie Clay and Concrete Masonry Banding Details. 0000001837 00000 n For positive bond breaking, it is essential the casting slab be 100% sealed with TILT-CRETE. Visually and physically inspect the slab to witness the entire surface has a definite sheen. Any dull spots must be recoated. Questionable areas can also be tested by dropping water on the surface. If the water beads-up or forms a bubble and does not penetrate the concrete surface, it is sealed. Any areas accepting penetration of the water must be recoated until a positive seal is achieved. PACKAGING 127 58 0000060358 00000 n Bond breakers will offer you some additional advantage such as: If you are planning to buy a bond breaker, have in mind the following factors before making a decision: Bond breakers are classified into two major groups: membrane-forming and non-membrane forming. Membrane forming bond breakers will hold water in the casting slab, and they are formulated to meet ASTM C-309, the standard specification for liquid-membrane-forming compounds. Like all construction systems, design decisions significantly influence field performance of the concrete masonry wall system. CONCRETE This premium-grade bondbreaker contains organic compounds that react with Evy%_FNZi-iYiF$wb*dPVEvVXi1w,H,M 4!}&r%Vr~ JR_yVI&f(^Vjrv{>Pg29SXeK= T Anchor water impermeable barrier. However, depending on the type of facing, considerations should be given to crack control in the facing material as well. Non - Staining Does not interfere with concrete placements Can be used as mould release agent as well PRODUCT INFORMATION Chemical Base A modified wax compound Packaging 25 l/gallon 200 l/drum Appearance / Colour Milky white 0000015427 00000 n Close this window and log in. Temperature Compatible: Excellent range for cold or hot climates. TILT-CRETE may be applied with a commercial hand sprayer, such as a Chapin 1949. When a bond breaker is needed at a construction joint, a curing compound, REGAN Vest: Inside Denmark's secret nuclear bunker During trowelling / finish stage, remove tear-off strip. This TEK focuses on non-structural cracking resulting from internal volume change of the concrete masonry. If you have any questions or would like to learn more, please contact us. When the transfer of out-of-plane loads between two panels separated by a control joint is not critical, or when fireresistance is not a controlling design feature, the control joint shown in Figure 3c can be used. An alternative to avoid having the vertical reinforcement cross the slip plane is to place the reinforcement in the next cell over. The dowels are typically greased or placed in a plastic sleeve to prevent bond and allow unrestrained longitudinal movement.